General data
General basic values
Speed at maximum performance
Compensation for valve play
Inlet valve opens/closes in degrees of crank angle
2°-/42°+
- before TDC+ after TDC/- before BDC+ after BDC
Outlet valve opens/closes in degrees of crank angle
34°-/2°-
- before BDC+ after BDC/- before TDC+ after TDC
Inlet valve stem diameter
Outlet valve stem diameter
Number of spark plugs/glow plugs required
Minimum engine oil pressure when idling
Maximum deformation of cylinder head
Minimum cylinder head height
Cooling system
Cooling system pressure (radiator cap opening pressure)
Thermostat opens at temperature
Cooling fan is switched on at temperature
Cooling fan is switched on at temperature
Ignition system
Ignition system values
Spark plugs/glow plugs NGK
Secondary resistance ignition coil
Initial coil primary resistor
Fuel system
Fuel system in general
Mixture processing manufacturer
Exhaust gas test values
General exhaust-gas-relevant values
Diagnostic socket location
Idling speed with manual gearbox
Brake system
Brake dimensions
Front axle brake disc thickness
Front axle brake disc thickness wear limit
Rear axle brake disc thickness
Rear axle brake disc thickness wear limit
Front axle brake disc diameter
Rear axle brake disc diameter
Front axle brake piston diameter
Rear axle brake piston diameter
Electrical system
Measuring values of sensors and actuators
Engine temperature sensor resistance at 0°
Engine temperature sensor resistance at 20°
Engine temperature sensor resistance at 25°
Engine temperature sensor resistance at 40°
Engine temperature sensor resistance at 50°
Engine temperature sensor resistance at 60°
Engine temperature sensor resistance at 80°
Engine temperature sensor resistance at 100°
Air gap of the crankshaft sensor in mm
Crankshaft sensor resistance
Injection valve resistance
General electrical system
Battery cold test current
Battery cold test current
In countries with a cold climate
350
Ampere
Generator type
with air-conditioning
A115IM 14V 50/90A
Generator type
In countries with a cold climate
A115IM 14V 55/105A
Alternator charging current
Alternator charging current
with air-conditioning
50 - 90
Ampere
Alternator charging current
In countries with a cold climate
55 - 105
Ampere
Rotor resistance
In countries with a cold climate
2,09 - 2,31
at 20°C
Control unit voltage
14,05 - 14,35
Volt
at 20°C
Consumables
Filling quantities and specifications
Engine oil specification
FIAT 9.55535-S2
SAE 5W-40
Manual gearbox oil specification
Cooling fluid specification
CUNA NC 596-16|ASTM D 3306
Brake fluid when changing
Brake fluid specification
Air-conditioning system refrigerant
Refrigerant specification
Air-conditioning system oil
Air-conditioning compressor oil specification
Lighting
Front light sources
Low beam
with halogen headlamp
H1 12V 55W P14,5s
Low beam
with bi-xenon
D1S 85V 35W PK32d-2
High beam
with halogen headlamp
H1 12V 55W P14,5s
High beam
with bi-xenon
D1S 85V 35W PK32d-2
High beam
Full-beam spotlight, with bi-xenon
H1 12V 55W P14,5s
Parking light
W5W 12V 5W W2,1x9,5d Longlife
Front direction indicator
Side direction indicator
WY5W 12V 5W W2,1x9,5d yellow
Rear light sources
Tail light
Taillight/brake light
P21/5W 12V 21/5W BAY15d
Stop lamp
Taillight/brake light
P21/5W 12V 21/5W BAY15d
Internal light sources
Change intervals
For service data
Engine control toothed belt change interval
every 120.000 km / 5 years
Engine control toothed belt change interval
under heavy service conditions
every 120.000 km / 4 years
Accessory drive belt test interval
every 30.000 km / once a year
Accessory drive belt change interval
every 120.000 km / 8 years
Air filter change interval
every 60.000 km / 4 years
Spark plug change interval
every 30.000 km / 2 years
Brake fluid change interval
every 60.000 km / 2 years
Engine oil and filter change interval
every 30.000 km / 2 years
Engine oil and filter change interval
at less than 10.000 km mileage per year
Once a year
Check car body and underbody
With each maintenance service.
Interior filter change interval
every 30.000 km / 15 months